Irish Grind Bowl Gouge Docs

  • document

    THE TOOL SHOP Sharpen Learn to 2 Progressively

    Sharpening the spindle roughing gouge The spindle roughing gouge is ... the Irish grind. Although it looks formidable with such a long edge, ... sharpen a bowl gouge I recommend the transition grind for new bowl turners. You work the

  • document

    Demo or Class: The Ellsworth Signature Gouge

    Bowl Gouge for Roughing, (Optional) “P&N” 5/8 inch (16mm) Bowl Gouge, sharpened like a Ellsworth with no wing. i.e. straight swept back grind (Irish grind). See John Jordan segment on AAW Sharpening DVD. 5/ 8” is available from www.packardwoodworks.com

  • document

    Burl - Heirloom Bowls

    www.woodturner.org 00 For this project, you’ll need: • 1/2" and 3/8" Irish-grind bowl gouges • 1/2" x /8" diamond-shaped shear scraper • 1/2" shallow-flute spindle gouge

  • document

    WOLVERINE GGRINDING JJIG IINSTRUCTIONS - Rockler

    Wolverine Grinding Jig to work best, your grinder and your grinding jig should both be ... fingernail grind! bowl gouge grind! side or Irish grind. Side Grind (Irish Grind) While attending many wood shows and symposiums, designers at . ONEWAY .

  • document

    Translucent Bowls - Eric Lofstrom

    Fingernail Grind Bowl Gouge Traditional Grind Bowl Gouge ee ORCE ORCE. My Bowl Gouges: (approx. angles) Irish Grind- used to remove nearly all wood inside & out, shear cut & shear scrape exterior.

  • document

    Demo of the Month - Southern Utah Woodturners

    Again using only the Irish grind bowl gouge he hollowed the inside leaving only a 1/8” thickness in the bowl's walls then the inside of the bowl was sanded to 320 grit. The piece was then placed in a Longworth chuck to remove the tenon from the bottom.

  • document

    Finger Lakes Woodturners

    duced the Irish Side Grind Bowl Gouge to David Ellsworth – who eventually promoted its use throughout American woodturning. FLWT Board of Directors Liam is known for a variety of turned work including bowls, hollow

  • document

    Setting-Up Your Woodturning Work Station – Part 1:

    With a properly ground bowl gouge you can rough out the bowl, turn the bowl, and shear scrape to finish the bowl. It is also an excellent tool for hollowing boxes, ... The grind most people recommend for a beginner is often called an Irish or Ellsworth grind.

  • document

    Message from the President - Utah Association of Woodturners

    3/8" Bowl Gouge sharpened to a long finger-nail (Irish) grind, 1/4" Spindle Gouge, 3/4" Round-Nose Scraper with Burr Removed, Morse Taper Screw Chuck, Barracuda 3 Scroll Chuck (or other small chuck), Sandpaper, Curved Surgical Clamps (to hold sandpa-

  • document

    60º ¾” to 1” - Geiger's Solutions

    Five Cuts with a Side-Ground Bowl Gouge By: Don Geiger ... or an Irish grind. The fifth cut includes instructions on using a micro-bevel gouge with a 70° bevel on the tip and one or more relief grinds. For information on accurately producing these grinds, visit:

  • document

    Don Geiger- Biography - Classic City Woodturners

    Don Geiger- Biography ... • Sharpening a deep- fluted bowl gouge with an Irish/Ellsworth grind. ... • Five cuts using a bowl gouge, how to prevent catches and how to obtain smoother surfaces that are more easily sanded. • When, ...

  • document

    TURNING WOOD BOWLS - Jim Rodgers' Designs in Wood

    O’Donnell, and Irish grinds. The length of the side grind, whether straight or radiused and the bevel and side angles are all a matter of personal ... The following technique is useful for new turners to use the bowl gouge to successfully complete the turning of a bowl.

  • document

    gouge Jig SVd-185 - Rockler

    Irish profi le. Swept back wings. ... Check your grinding frequently to ensure that the gouge acquires an even shape. Grind ... This graph shows examples of shapes which you can achieve on a bowl gouge at various jig settings and edge angles.

  • document

    G H Package Contents F

    A 60° Ellsworth or Irish Grind on a deep-fluted bowl gouge 60º ¾” to 1” Spindle Gouges with a 40° bevel Angle selection rod position: ORANGE

  • document

    July 2014 Presidents Letter

    Sharpening an Irish Grind Bowl Gouge Sharpening D-Way Gouges Lyle with Jamieson Grind Cindy Drozda – Sharpening Gouges NEW MEMBERS: Patty Beonde’, 84 SW Hideaway Place, Stuart, FL 34994 772-475-0793 (c) [email protected]

  • document

    Shavings - Mid Minnesota Association of Woodturners

    classic 'Irish grind' bowl gouge. His vast knowledge and experience plus his natural sense of Irish humor has made him one of the top demonstrators since he first came to America back in the mid- í õ ô ìs." Twenty-one members responded to our initial email blast.

  • document

    Finger Lakes Woodturners I

    Work,” but he shows the same expert flair when it comes to bowl turning. I was also told that the use of the projector, along with a smaller membership (and a chair for everyone), made it easy for everyone to see what was happening.

  • document

    Regular Monthly Meeting Message from the President

    done, he takes his “big bowl gouge”, a ¾” bowl gouge with a swept back Irish grind to take out the rest of the inside. As you ap-proach the natural edge, make sure the flute is facing horizontal, or the direction of your cut so it won’t “skate” and ruin the edge.

  • document

    Gouge Jig SVD-185 - Tormek

    GoUGE JIG SVD-185 69 Turning Gouges Bowl and Spindle Gouges Note the settings on the Profile Label and put it in on the ferrule. A set of labels comes with the jig.

  • document

    How to turn a crotch form B y Dinyar B. Chavda (July 2003)

    natural -edged bowl, like the one shown in CrotchBowl, or ... I use either a regular bowl gouge or one of my Ellsworth/Irish Grind -type gouges. The piece is starting to take shape in Fig 5, although the top ... If I had gone with my original design of an open bowl, I would use a bowl gouge to

  • document

    Search Go Home Store Locator Catalog Sales Flyer CLASSES ...

    Tools Required: One Each – Bowl Gouge, Spindle Gouge & Skew To Be Sharpened Correct sharpening skills are crucial to success at woodturning. Instruc- ... nose angles for an Irish grind, Ellsworth grind, fingernail grind for bowl gouges and spindle gouges; correct sharpen-

  • document

    Several of our members will give “mini demos”

    Placed between centers the birch is roughed out with a bowl gouge (Irish grind) because a roughing gouge sends the chips, bark, dirt and grit right back into your face and body making a mess. The bowl gouge is placed at 45 degrees, rubbing the bevel and moving from left to right

  • document

    Sharpening for Woodturners - Leland Studios

    A good idea for someone who would like to sharpen a side ground gouge (Irish Grind David Ellsworth Grind, ... The next step is to discuss each type of tool (scrapers, spindle roughing gouge, bowl & spindle gouge, skew and parting tools) ...

  • document

    New Mexico Wood Turners; Vol. 11 Issue 5 May 2010 High Desert ...

    Bill passed around a double-ended One-Way bowl gouge that is V-4, or 4% Vanadium. He also showed us some ¼” round HSS rod for tools available through ... designs, the English grind, which has a 45 Titanium Nitrite as a coating on HSS helps lubricate the surface and toughens the steel.

  • document

    project half log bowl A4 - Galloway Woodturners

    It is safest to use a gouge ground with some degree of sweep back to the edge – called variously the Irish Grind, ... If necessary level off the top surface with the bowl gouge, cutting on centre level from outside to centre. 14.

  • document

    Irish Woodturners’ Guild

    Irish Woodturners’ Guild • … someone who regularly attends the Wednesday workshops would volunteer to ... a long-grind bowl gouge in pull cut mode. Initially he focused only on production of an ogee (‘S’) profile, which he achieved quite quickly.

  • document

    MWT december 2008 - Maine Woodturners

    as David applied a bowl gouge with an Irish grind on the center of the bowl and power cut his way to the edge. With half or so turned out he moved to turn the rim. He undercut to start the movement of the bottom

  • document

    toolday 2010 order form - MinnDakWoodturners

    Bowl gouge jig $15 Holds bowl gouge for sharpening (Irish / Ellsworth grind) laser pointer QTY Cost Description wall thickness system $60 Helps you determine where your cutter is in relation to the wall thickness of your hollow vessels.

  • document

    GCWA Newsletter

    May 1999, page 2 1999 GCWA Spring Retreat The member registration fee for the entire weekend includes participation in all events, including demonstrations, hands-on

  • document

    March General Meeting

    left shows a typical bowl gouge. The purpose of the deep flute is to eject the wood chips from the inside of a bowl. The shape of the ... Ellsworth, is also known as the Irish grind and the fingernail grind. In a swept back gouge, almost all of the cutting action

  • document

    Echos From the “BAT” Baltimore Area Turners Cave

    He brought the Irish Grind to the US. David Ellsworth was his first convert, he said. Lately, he has been making ... After roughing out the center bowl he used his bowl gouge held almost upside down to attain a good finish. He showed a spindle

  • document

    Palmetto Woodturner ©

    Irish Woodturning Guild's Symposium in 2012. For the first part of the day, Ashley will demonstrate fine spindle turning in one of her sea urchin ornaments. ... will be using the same 40/40 grind on a bowl gouge that she was using for the spindle.

  • document

    Basic Tool Groups - N.J. Woodturners

    Bowl Tools Bowl Gouge Known by its deep flute, ... Many grinds used at turners individual preference – Irish, Ellsworth, Mahoney, Traditional, Key, Traditional grind is very straight and best used for cutting straight across bottoms. Platform ground straight across. Swept back wings are best ...

  • document

    Galway chapter NEWS

    we were all comfortable using a bowl gouge with the “Irish Grind” and David’s hollowing tool. Whether or not we ever put into practice what was demonstrated that day is another question but we will no longer wonder “how did he do that”?

  • document

    Dublin Chapter at the Terenure College Fun Day

    ½ bowl gouge with fingernail grind for forming the outside profile. This was a gentle ogee or ‘S’ form, going smoothly from centre to rim. ... Maybe its something in the Irish psyche, but many people I know seek sanctuary from good weather in a gloomy pub or snooker hall.

  • document

    Beginner’s Corner: Some Light Along The Path

    The bevel of a tool refers to the area directly underneath the cutting edge of a tool such as a scraper or a gouge. This area has different uses depending on the tool, but by far the most common reference to a bevel is for the gouge.

  • document

    Galwa Chapter NEWS

    Chonamara was awarded the Irish Rural Link National Award 2012 in Letterfrack recently. Galway Chapter NEWS ... After truing the face with a bowl gouge, he used a ½″ bedan tool to cut a dovetailed foot to suit one of his chucks.

  • document

    Segmented turning by Ron Schiffner - MinnDakWoodturners

    Bowl gouge jig $10 Holds bowl gouge for sharpening (Irish / Ellsworth grind) laser pointer QTY Cost Description wall thickness system $50 helps you determine where your cutter is in relation to the wall thickness of your hollow vessels

  • document

    Gouge Jig SVD-185 - Industributiken

    Irish profi le. Swept back wings. ... Check your grinding frequently to ensure that the gouge acquires an even shape. Grind ... This graph shows examples of shapes which you can achieve on a bowl gouge at various jig settings and edge angles.

  • document

    Woodturning Safety Rules

    Produced by JL Rodgers, Inc – 236 Briar Drive – Martinez, CA 94553 © All right reserved, 2007 Page 1 Woodturning Safety Rules . 1. Know Your Equipment and Yourself.

  • document

    New Mexico Wood Turners, Vol. 12, Issue 3 March 2011 High ...

    Sharpening started with a bowl gouge provided ... showed the way to form an Irish or Ellsworth grind that has many uses in bowl turning. He went on to demonstrate use of the skew, the angles, the cutting area and sharpening, including honing.

  • document

    Echos From the “BAT” Baltimore Area Turners Cave

    troduction of the Irish (swept back) grind of gouges; he prefers the English (not swept back) grind for bowl turning. He eschews the skew and uses a ... gouge hollows the bowl Next was an oil lamp. A 1 ½” hole was drilled in the Red-

  • document

    THE CHIP FLYER

    PAGE 2 PAGE 2 THE CHIP FLYER NO. 70 NO. 70 K aren Russell announced that she was here to inspire us and she succeeded. Forget the myths about art: I can’t

  • document

    THE CHIP FLYER

    Oct 21 Basic Bowl Turning demo by Doug Newlove ... you made, one with that special grind or simply come with your questions. ... incorporate the Ellsworth Gouge as there has been quite a bit of informal discussion about it in recent